Pay in installments of $1006.62 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 29 - Aug 3
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
PSS-Dichtung 5' Welle, 8' StevenrohrDie PSS Wellendichtung Typ B ist eine mechanische Gleitringdichtung. Die Dichtflche entsteht zwischen den ebenen Flchen des rotierenden Edelstahlrotors und dem stationren Kohleflansch. Der stationre Kohleflansch wird mit Schlauchklemmen an der Vorderseite des Balges und das hintere Ende des Balges ber das Sternrohr befestigt und wird mit Schlauchklemmen gesichert. Der Edelstahlrotor ist auf der Welle vor dem Kohleflansch montiert. Der Edelstahlrotor
Die PSS Wellendichtung Typ B ist eine mechanische Gleitringdichtung. Die Dichtfläche entsteht zwischen den ebenen Flächen des rotierenden Edelstahlrotors und dem stationären Kohleflansch.Der stationäre Kohleflansch wird mit Schlauchklemmen an der Vorderseite des Balges und das hintere Ende des Balges über das Sternrohr befestigt und wird mit Schlauchklemmen gesichert. Der Edelstahlrotor ist auf der Welle vor dem Kohleflansch montiert. Der Edelstahlrotor wird verwendet, um den Balg zu komprimieren, bevor der Rotor mit Stellschrauben an der Welle befestigt wird. Diese Kompression (Vorspannung) sorgt für einen konstanten Kontakt zwischen den beiden flachen Seiten des Edelstahlrotors und des Kohleflansches. Dadurch kann die PSS Wellenabdichtung die variable Vorwärts- und Rückwärtsbewegung - bedingt durch den Propellerschub - ausgleichen. Der Kohlenstoffflansch ist zum Wellendurchmesser überbohrt, so dass er um die Welle herum 'schwimmen' kann und somit die meisten Fehlausrichtungs- und Schwingungsprobleme ausgleicht. Der Rotor aus rostfreiem Stahl ist durch zwei O-Ringe, die in die Bohrung des Kragens eingelassen sind, gegen die Welle abgedichtet. Diese O-Ringe rotieren mit der Welle und dem Edelstahlrotor und unterliegen keinem Verschleiß während des Betriebs.
Temperaturgrenzen: -13°F bis 425°F (-25°C bis 220°C)
Druckbegrenzungen: 3,5 BAR (50 PSI)
Grenzwerte für die Wellendrehzahl: 7.000 U/min.
Kohlenstoff-Graphit: Auf 4 HLB geläppt (0,00000044' Toleranz)
316SS / Nitronic 50: Gegenüber 9 Ra
Balgmaterial: Dornförmiges Silikon / Gewebe
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.3 ★★★★★
Based on 21 reviews
Sort
Product Reviews
★★★★★ 5
Test fit to make sure it connects
When I revived it I thought it had looked a little too small until I compared it, I test fitted it and at first I thought it was a tad bit bigger but realized the more I pushed it in the more it went very tight fit and my car is running healthy. Installation is a pain but go to YouTube and search the “” the 50’s kid”” Who has two methods to getting them on, I went the intake removal route to replace additional parts.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on January 8, 2020
★★★★★ 5
Cheap Replacement
These are an easy replacement for anyone who owns a BMW m52/m54 engine that has PCV issues. My car was burning about 1 quart every 1,000 miles. The parts are direct fit and install fairly easy. If there is resistance, lube the hole or o-ring up with some grease and it will slide in easier. Took me about 2 hours start to finish. My mechanic recommended that I remove the intake manifold to do the job. I don’t see how you could do it without removing the intake manifold.
These parts probably won’t last as long as true BMW parts but on a 20 year old car I don’t see the benefit in using genuine BMW parts. Cheap stuff will suffice; worst case it doesn’t last quite as long.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 6, 2021
★★★★★ 4
NOT TOO HARD TO INSTALL...
This CCV kit seems adequate.
People say that because the hoses supplied with these kits are more brittle than the genuine BMW parts, these are tough to install... But they're really not.
The ends on these hoses SWIVEL and you can sort of eyeball which way you need the fitting to be pointing BEFORE you put them on your manifold... They swivel, but they're tight and it takes a little force to turn them.
ALSO, a little dab of silicone gel or a spray of silicone out of the can, into the fittings on these makes a world of difference when clicking them on...
For the price, I highly recommend the kit.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 14, 2025
★★★★★ 5
Great value
I recently had to replace the starter on my 2001 325i E46 with about 150k miles. While I had the intake off, I figured it would be a good time to replace the CCV because I was unsure if it had ever been done. My old CCV literally fell apart as I removed it, so I'm glad I replaced it.
The new parts were a little tough to put together, but overall came together well enough. A lot can be forgiven for the price. I would recommend assembling the system before installing in your vehicle to get a good sense of how it all goes together and to hopefully loosen up the fittings just a tad before installation. 50skid on youtube has a great DIY for doing this job.
I only finished this job yesterday, but my car has been running great. I can't yet confirm, but this may have solved my running lean problem.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on January 27, 2023
★★★★★ 3
Cheap plastic parts -- good fit
They are what they are: Cheap plastic parts. They fit, but long-term durability will be a challenge. Probably will buy from FCP Euro going forward (and just did for a fuel line replacement).
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 12, 2024