V1W Z-Pro (Red Cat Ascent Kit)

V1W Z-Pro (Red Cat Ascent Kit)V1W Z Pro (Red Cat Ascent Kit) NOT INCLUDED: Chassis and Links. THIS LISTING IS A BUILD KIT! Don't forget to purchases your chassis rails. They come in either Aluminum or Carbon Fiber. Link kits come with brass Lowers and Delrin Uppers. What you get: Plastic Parts Set (Skid, Body Post Mounts, Bumpers, Side Bat Tray (Revolver Motor Only), CMS Spacers, Motor Plate Brackets, Axle Side PH Mount), Aluminum Motor Plate, Aluminum Lay down CMS PH Mount (v2),

V1W Z-Pro (Red Cat Ascent Kit)

NOT INCLUDED: Chassis and Links. THIS LISTING IS A BUILD KIT! Don't forget to purchases your chassis rails. They come in either Aluminum or Carbon Fiber. Link kits come with brass Lowers and Delrin Uppers.

What you get: Plastic Parts Set (Skid, Body Post Mounts, Bumpers, Side Bat Tray (Revolver Motor Only), CMS Spacers, Motor Plate Brackets, Axle Side PH Mount), Aluminum Motor Plate, Aluminum Lay-down CMS PH Mount (v2), Hardware (6 - M3x6, 20 - M3x8, 4 - M3x10, 2 - M3x12, 5 - M3x16, 3 - M3x30, 4 - m3x35, 10 - M3 Nylock, 3 - M3x12 Flat)

Assembly Note: The included Axle Side Pan hard Mount goes in place of the Shock on the axle. (Remove the Stock Pan-hard) You will need to relocate your shock to the lower link mount with and M3x30mm with Lock Nut. Mount the front shocks Upside Down. The front upper link would mount to the outside of the link pocket. Front Upper Links Mount to the outside of the axle tab, not in the slot.

Modifications: Front Shock Mounting location will be moved to the outside of the lower links with a longer bolt and screw. We recommend mounting them upside down. Axle side Pan hard will be removed. STH Panhard will be installed in place of the front right shock on top of the axle. Needs Custom Links, Swap Motor Plate with the provided Motor Plate.

Links: CUSTOM LINKS REQUIRED... STOCK ASCENT LINKS WILL NOT WORK.
We have completely recalculated the link geometry to better suit the Z-Pro Chassis, you will be unable to use the stock links. You will either need to make your own links or we have teamed up with D-Links for a ready made Link kit to make your life easier.

D-Links Link Kit can be found Here: Contact D-Links
D-Links Improved Steering Linkage: https://d-links.us/redcat-ascent-brass-high-cleara...

Link Measurements Eye-to-Eye: Upper Links - (Front 90mm, Rear 102mm), Lower Links - (Front 102mm, Rear 128mm Bent), Panhard Link - (90mm Same as Front Uppers)

Z-Pro Ascent Motor Mount Plate: The Motor Mount has been redesigned to fit the Z-Pro Chassis and lower the motor as much as humanly possible for optimal performance. The motor mount consist of one 3mm 6061 Aluminum Plate and two Motor plate brackets.

Ascent Z-Pro Skid (STH-0184SKA): The skid has been completely redesigned and to accommodate the eight degree slope in the chassis while keeping the drive shaft inputs parallel with the ground for more efficient drive angle.

Side Battery Plate (STH-0184SBT): The Side Battery Plate is designed to be use if you are using a small revolver type motor. This will allow a small battery pack or the ESC and Receiver to sit closer to the center line of the chassis with the weight down low.

Panhard/Laydown Servo Mount v2 (STH-0184Lv2): We used the Laydown Servo Mount to maintain a low profile up front along with a custom designed Panhard mount that is mounted to the stock axle side shock location. Shocks will need to be mount on the outside of the lower link mount.

Front Bumper Mount (STH-0184BFA): The Front brace is design to receive the stock front bumper and allow you to use the stock Body clip should you decide to use the stock body. Our body mount pods will come with this kit allowing you to us any body with the standard 6mm body posts. In the rear, you can use the stock body post mount flipped upside down with the stock body posts.

(Optional Purchase) Sliders (STH-0184HCS): We used the Z-Pro Aluminum Sliders to complete this kit. The sliders will sit just on the inside edge of the body. You will need to trim the body if you want the sliders to be visible and capture the edge of the body.

(Optional Purchas) Rear Battery Mount (STH-0184BER): If you want to keep the weight mounted in line with the center of the chassis, you can use the optional Rear Battery Mount.

Hardware: Most of the hardware can be recycled from your Ascent as you take it apart. We do provide hardware that can not be scavenged from the Ascent and to include some uncommon hardware.

Due to the nature of 3D printing, items may contain tiny visual blemishes. Items may require some trimming and painting for optimal visual appeal/fit; similar to what you would expect to do with model parts.

IMPORTANT: Do not use power drivers on 3D printed parts. Over tightening printed parts and cause premature cracking and crushing. Always ensure you hardware will not bottom out in the screw pocket. This can also cause at 3D printed part to break prematurely.

Printed Parts - These parts will be printed in Black (Unless otherwise requested) using advances slicing methods for maximum strength. All 3D printed parts come with a lifetime replacement guarantee. If you break a part, simply send us a photo and your order number. The photo is simply to evaluate for common issues and help identify potential improvements to existing designs.

Contact us @ [email protected] or PM us @ Spare-Time Hobbies on Face Book.