SKU: 70900907411

PRO-TECH EXTERNAL BULL NOSE 7/8' X 31MM FULL RADIUS 22MM 1/2' SHANK KP372461

Sale price$342.86 Regular price$380.96
Save 10%

Pay in installments of $95.24 with ShopPay, AfterPay and Klarna

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Aug 24 - Aug 29

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

PRO-TECH EXTERNAL BULL NOSE 7/8' X 31MM FULL RADIUS 22MM 1/2' SHANK KP372461Half Round Bull Nose Bit Carbide Tipped This router bit is used for creating a convex shaped profile on the side of the workpiece in one pass producing a perfect half radius bull nose profile Design helps minimize kickback Smooth edge requires little or no sanding before applying finish This router bit has a 12,7 mm shank (shaft) that will fit most large routers. Please ensure that you select a router bit with a shank (shaft) size that will fit into

Half Round Bull Nose Bit

 

Carbide Tipped

This router bit is used for creating a convex shaped profile on the side of the workpiece in one pass producing a perfect half radius bull nose profile

  • Design helps minimize kickback
  • Smooth edge requires little or no sanding before applying finish

This router bit has a 12,7 mm shank (shaft) that will fit most large routers. Please ensure that you select a router bit with a shank (shaft) size that will fit into your router collet.

 

 

PRO-TECH router bits are manufactured in Taiwan.

 

consider safety for your health and the people around you

General safety suggestions:

It is advisable to always have the following items nearby and in a good condition

  • Eye protection clean and scratch free
  • Hearing protection quality earmuffs
  • Dust masks discard old and dirty masks
  • Gloves for easy handling of material and hand protection
Wear Gloves
Eye Protection
Hearing Protection
Dust Mask

To use router bits safely (and to get the best results from your router), the router bits need to be installed properly into the router's collet. Improper installation of your bits can cause excessive chatter and could increase the likelihood that the bits will break when in use. 

Clean and sharp

First of all, before beginning any routing operation, check your bits to make sure that they are clean, relatively free of pitch, and most of all, sharp. If the bit is dull, chipped, is excessively burned or has any other defect, it should be sharpened or replaced before use. 

Correct collet and collet nut fit

Most router collets have a recess (groove) that needs to click into a circlip that resides inside the collet nut. Failing to ensure that the collet 'clicked' into the collet nut will cause you to struggle to remove the router bit after tightening. This could cause the collet to break or be removed by a technical repair centre.

 

Correct fit inside the collet

When installing the bit into the collet, do not tighten the collet with the bit 'seated.' Instead, insert the bit until the shank (bit shaft) reaches the bottom of the collet, then ease it out about 2 mm before tightening the collet.

When the bit is tightened, there should be no less than  2/3 's of the length of the shank in the collet. If your bit has a shank that is too short, then the bit should be replaced. 

 

Safety gear

There are a few other safety measures to keep in mind whenever you use your router. First of all, remember to always wear appropriate safety gear as indicated above.

Correct speed setting

Second, be sure to set your router to the proper speed for your router bit. Setting your router to an incorrect speed will not only affect the router's performance, but also can cause the bit to break much more easily and even cause bodily harm. The speed at which a router bit turns can be important. The typical router runs at about 22,000 rpm, which is fine for most bits. But as the diameter of the bit increases, you ll want to slow things down.

Also, before beginning any routing operation, be certain that you give the router's motor time to come up to full speed for the chosen setting. Beginning to cut before the bit is at full speed can give less than desired results. 

Observe the following at all times

  • Wear a protective face shield or Safety Glasses to prevent eye and face injury.
  • Wear ear plugs or ear muffs to protect your hearing.
  • Use a respirator or dust mask to give protection from dust particles. Wood dust may remain in the air for hours after using power tools.
  • Always read and follow router operator's manual instructions.
  • Make sure that router rpm's and the bit selected match.
  • Dress properly. Wear short sleeves, no loose fitting clothes, proper footwear and no jewellery. Tie back long hair.
  • Always be sure the router is unplugged before replacing bits and that the switch is off before connecting the router.
  • Be sure the router bit has completing stopped spinning before sitting the router down.
  • Be sure bits, clamps and attachments are secure before starting up.
  • Keep children, pets and visitors at a safe distance.
  • Be especially cautious when working small pieces.
  • Keep hands and fingers away from revolving bits and cutters.
  • Do not operate routers in moist or wet areas.
  • Always grip tool tightly and be prepared at start-up to resist the motor torque.
  • When using a router table, make sure on/off switch is easily accessible.
  • Learn the sound of your router and shut it off at any unfamiliar sounds or irregularities.
    Never start the router with the bit in contact with the material.
  • Always feed in the proper direction, against the direction of bit rotation.
  • Maintain equipment. Replace worn parts, discard worn-out bits and check router periodically. Clean parts with appropriate solvents.
  • Don't operate a tool if you are tired or under the influence of medication, drugs, alcohol or while smoking.
  • Check wood for nails, screws or loose knots before routing.
  • Keep your mind on your work, avoid distractions, work at a comfortable pace and stop before you get tired.

Do a dry run

  • Place the router on the final work surface and test you cut by moving the router over the whole are to cut with THE ROUTER SWITCHED OFF
  • You do not want to waste an expensive piece of wood
  • You do not want to start all over
  • Never met anyone with spare fingers - SAFETY

Using a Router in a Router Table

Router Table Safety

Although most router bits are small, they can be potentially dangerous and should deserve your attention and respect.

1 Use push sticks or a push block to position your hands a safe distance from the router bit.

2 Use large-diameter bits only in a router table. Using bits over 25mm Ø (diameter) in a handheld router can possibly cause you to lose control of the tool and harm yourself or bystanders.

3 Always wear a dust mask as well as eye and hearing protection.

4 Take light cuts. Heavy cuts invite kickback. If necessary, move the fence closer to the bit or switch to a larger guide bearing/bush.

5 Use a featherboard (anti-kickback device) to support the workpiece against the router table and/or fence.

6 Never climb-cut. Always feed the stock from right to left. Against the rotation of the router bit. (see illustration)

7 Avoid routing small stock. Instead, rout a larger piece and cut it to size afterwards. If you absolutely have to profile a small piece, build an suitable jig or secure the workpiece.

8 Always use a guard. If the fence didn t come with a guard, make your own.

9 Never start the router with the bit in contact with the material.

10 Don t force the router bit or overload the router. Excessive heat is an enemy.

11 Secure/fasten the router in the base before starting/switch on the router.

12 Don t bottom out the bit in the collet or partially insert the bit. Instead, completely insert the bit, and then back off approximately 2 mm. At least 2/3 's of the router bit shank should be inside the collet.

13 Be sober and not under the influence of medicine that causes a lack of concentration

14 Tidy up your workshop to ensure the ability to move freely with enough room around the router table

Part No. Shank dia. Bull Nose Ø Cutting Height Radius (r)
KP372461 1/2 inch 55/64 inch 1 7/32 inch 27/64 inch
12,7 mm 22 mm 31 mm 11 mm

 

Length of Shank: 38 mm

 

 



KP372461Router Bits > Bull Nose > External Bull Nose
Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 70900907411

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.0 ★★★★★
Based on 20 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
A
Verified Purchase
Amazon Customer
Alexandria, US
★★★★★ 5
30 amp extension cord
Size: 25-Foot, Style: Standard End
Great 30 amp power cord Great quality just as described
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 22, 2026
T
Verified Purchase
Texas reviewer
Houston, US
★★★★★ 4
Have used a Camco cord with our camper van, wanted an extension with the same quality.
Size: 25-Foot, Style: Standard End
Good design, solid plugs just like their power cords that attach directly to the van. We ended up having to purchase 2 to put them together to get the length we wanted, one came yesterday, the other today. The one that came yesterday came with a nice strap with a handle that makes it easy to bundle the cable up when not in use, and makes it easier to carry. The second one we purchased that came today, did NOT have a nice strap/carrying handle. I thought for sure that I saw that this carrying handle noted in the product description, but today I can't find it there. So, a great cord, should not melt like some of the others, since it is identical in construction to the RV cord we have used for 5 years.....just wish they all came with the nice carry handle. Would have given it a 5, but with 2 of these ordered 1 day after the other, and they are not supplied with the same nice accessory, we discounted the review a tick.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on January 31, 2024
R
Verified Purchase
RickyDoo
Whiting, US
★★★★★ 5
Use as shore power routing cable to and from Victron Multiplus nverter
Size: 50-Foot, Style: Standard End
I cut the ends off this and used it for extending in the original 30A shore circuit to and from my power center to my 3000W Victron Multiplus inverter. Very flexible and easy to run. It was a bit dicey to remove the black outer support material without injuring the conductors - used a table knife. You want to leave a little cabling on the ends so that you might use them for other purposes. For example, to bench test the Victron Multiplus. Per foot it was less expensive than other options and worked better IMHO.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 28, 2023
T
Verified Purchase
Texas Bill
Charlottesville, US
★★★★★ 5
Glad I bought this one
Size: 25-Foot, Style: Standard End
There were other less expensive options but I'm glad I bought this one as it's a brand that I recognize and it seems heavy duty and well-made to me, and the cable feels just like the one coming out of my RV. I used this extension cord on a recent ten day trip for extra reach to a generator for running various appliances, including the air conditioner. I checked it periodically for any signs of overheating and it never felt abnormal at all to me. Just my own experience and opinions here, yours may differ. Thanks and good luck!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on September 18, 2024
A
Verified Purchase
A Novo
Los Angeles, US
★★★★★ 5
Great price, excellent product!
Size: 30-Foot, Style: Standard End
The Camco Power Grip 30-Ft 50 Amp RV Extension Cord has been a fantastic addition to my RV equipment. It offers both reliability and convenience, making my camping experience so much better. One of the standout features is the robust construction. The cord is heavy-duty, yet flexible enough to maneuver easily, even in tight spaces. The 50 Amp rating provides ample power for my RV’s electrical needs, ensuring that all my appliances run smoothly without any issues. The Power Grip handles are a brilliant touch, making it easy to plug and unplug the cord without straining my hands. The design is well thought out, and the bright color ensures that the cord is always visible, reducing the risk of tripping or other accidents. I also appreciate the weather-resistant coating, which provides extra durability and protection against the elements. It’s held up well in various weather conditions, from rain to intense sun, without any signs of wear or degradation. Overall, the Camco Power Grip 30-Ft 50 Amp RV Extension Cord is an excellent investment for any RV owner. It combines durability, ease of use, and reliability, making it a must-have for a hassle-free camping experience. Highly recommended!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on November 8, 2024

recommand products