16GB DDR4-2400 ECC RDIMM - TAA Compliant

Axiom’s 16GB DDR4-2400 ECC RDIMM delivers enterprise-grade reliability, speed, and power efficiency for servers and workstations that demand consistent performance and data integrity. Built on the latest evolutionary DDR4 design, these modules are engineered to reduce downtime, safeguard critical workloads, and support dense memory configurations in demanding data-center environments. With DDR4 you gain notable improvements in single-DIMM performance—up to 30% faster than previous generations—while scaling power efficiency and memory bandwidth as you expand across multiple DIMMs. This memory is explicitly designed for mission-critical applications, including virtualization, database management, and enterprise computing, where stable, error-free operation translates directly into improved service levels and total cost of ownership. The 16GB ECC RDIMM variant combines error-correcting capability with a registered memory design to optimize signal integrity, timing, and reliability in multi-socket servers and workstation platforms. And as a TAA-compliant component, it meets procurement requirements for government and enterprise environments, offering a trusted upgrade path without compromising compliance or performance.

• 16GB capacity on DDR4-2400 speed (DDR4-2400 MT/s) with ECC on a Registered DIMM (RDIMM) architecture for robust error detection and correction, reducing the risk of data corruption in critical workloads.
• Enhanced reliability through ECC (Error-Correcting Code) protection and registered buffering, which helps maintain data integrity and signal stability in systems with multiple memory channels and higher memory bandwidth demands.
• Improved power management and efficiency that leverages the DDR4 generation’s architectural advances, delivering lower idle power and cooler operation in dense, high-density server racks and data-center environments.
• Designed to scale effectively in multi-DIMM configurations, with performance benefits highlighted in 3DPC (three DIMMs per channel) scenarios, where memory bandwidth and throughput increase as memory is expanded across channels.
• TAA compliant and ready for enterprise procurement, ensuring compliance with government and corporate standards while delivering consistent performance for mission-critical applications and virtualization workloads.

Technical Details of 16GB DDR4-2400 ECC RDIMM - TAA Compliant

• Capacity: 16GB
• Memory Type: DDR4 ECC RDIMM
• Speed: 2400 MT/s (DDR4-2400)
• Form Factor: Registered DIMM (RDIMM)
• ECC: Yes
• Compliance: TAA Compliant
• Pin Count: 288 pins
• Notes: Exact specifications may vary by SKU; refer to the supplier’s specifications for your exact part number.

how to install 16GB DDR4-2400 ECC RDIMM

Installing DDR4-2400 ECC RDIMM memory is straightforward, but following proper handling and installation steps helps ensure you get the full performance and reliability benefits. Begin by powering down the server or workstation and disconnecting it from any power source. Ground yourself to prevent static discharge, and locate the memory slots on the motherboard that support RDIMM modules. When handling the module, hold it by the edges and avoid touching the gold contacts. Align the notch on the memory module with the key in the slot, then apply even pressure on both ends of the DIMM until the latches snap into place, locking the module securely. After installing one or more DIMMs, re-seat any previously installed modules to confirm proper seating. Reconnect power and boot into the BIOS/UEFI to verify that the memory is detected and operating at the configured speed. Run a memory diagnostic tool or a built-in memory test to ensure stability and to confirm there are no errors. Finally, monitor system temperatures and performance during initial workloads to validate the memory configuration under real-world conditions. If you are upgrading an existing system, ensure compatibility with your motherboard’s memory controller and verify that your operating system and firmware are updated to support DDR4 ECC RDIMM configurations. Correct installation and thorough testing maximize uptime and ensure that your server or workstation can take full advantage of the 16GB DDR4-2400 ECC RDIMM’s capabilities.

Frequently asked questions

• Q: Is this memory ECC RDIMM suitable for my server or workstation?

  A: Yes. This 16GB DDR4-2400 ECC RDIMM is designed for enterprise servers and workstations that require error-correcting capabilities and registered memory for improved stability and signal integrity. Always verify motherboard compatibility with ECC RDIMM in your QVL or vendor documentation before purchase.

• Q: What workloads benefit most from DDR4-2400 ECC RDIMM memory?

  A: Virtualization, large-scale databases, ERP systems, high-availability applications, and other memory-intensive enterprise workloads benefit from ECC protection, higher memory capacity, and the reliability of RDIMM architecture. The combination of ECC and registered memory helps prevent data corruption and reduces downtime due to memory-related errors.

• Q: Is this module compliant with Trade Agreements Act (TAA)?

  A: Yes. The module is TAA compliant, making it suitable for government procurement and enterprise deployments that require compliance with trade regulations while delivering enterprise-class performance.

• Q: How does DDR4-2400 performance compare to previous generations?

  A: DDR4 offers faster data transfer rates, improved memory bandwidth, and better power efficiency compared to previous generations. In single-DIMM configurations, you can expect up to a 30% performance uplift, and in multi-DIMM per channel environments (such as 3DPC), performance scales more substantially, delivering as much as 65% faster throughput due to improved memory bandwidth and latency characteristics.

• Q: How can I ensure compatibility and optimal performance after installation?

  A: Start by checking your motherboard’s memory compatibility list and ensuring it supports DDR4 ECC RDIMM modules. Update BIOS or firmware to the latest version, enable memory interleaving if available, and run comprehensive memory diagnostics to validate stability. Use correct configurations in the BIOS (e.g., enabling ECC, setting appropriate memory speed) and monitor performance with workload-specific benchmarks to ensure you’re getting the expected benefits from the upgrade.