Pay in installments of $94.88 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Sep 1 - Sep 6
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
ETS 1993-1995 Mazda RX7 Front Mount IntercoolerFeatures : Large 24x9x3. 5 Bar and Plate Core (4" available in drop down menus) Eliminates Knock at high boost levelse Requires removal of bumper support Available in anodized Black, Blue, Gold, and Red. Installation Details: Requires Bumper Support Removal and Core Support Cutting Very Clean Set up Exterior Appearance Details: Fills Whole Grill with Core Work with USA and JDM fog lights Fills the grill on most aftermarket body kits Killer Look !
Features :
- Large 24x9x3.5 Bar and Plate Core (4" available in drop down menus)
- Eliminates Knock at high boost levelse
- Requires removal of bumper support
- Available in anodized Black, Blue, Gold, and Red.
Installation Details:
- Requires Bumper Support Removal and Core Support Cutting
- Very Clean Set up
Exterior Appearance Details:
- Fills Whole Grill with Core
- Work with USA and JDM fog lights
- Fills the grill on most aftermarket body kits
- Killer Look !
Performance
The performance of this unit is second to none. We developed it on our shop car (yellow FD in the pictures) which runs a T66, Haltech and all other supporting mods. When we first put the car together it had an Apexi FMIC kit on it we saw decent results but the charge air temps would creep up to 140-150 degrees. Slight detonation would occur in 3rd, 4th and 5th gears as observed on the J&S Knock sensor unit. Also because the tanks were wide and the core was small, the coolant temps were regularly over 210 degrees. All of this was with a pump gas tune at 21psi (10.5 AFR - 10 degrees ignition timing). When we switched to the kit pictured above the charge air temperatures dropped to 110 degrees and the highest we have ever seen is 122 degrees. This reduction in charge air temperature has allowed us to run 23psi regularly on pump gas with no detonation. In addition to the reduced charge air temperatures, the coolant temps dropped to 185-195 degrees and never exceed 200 degrees. All of this is with a stock bumper. We have had a handful of customer cars with body kits that see even larger temp reuctions. Typical results for a T66 turbo at 20psi is 95-110 degree charge air temperatures and 180-185 degree coolant temperatures. In addition to the low temperatures these kits provide, the ETS intercooler kit completely fills the stock bumper opening with core and body kits much better than any other kits we have seen with it's ultra wide 30" tank to tank dimension.
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.7 ★★★★★
Based on 16 reviews
Sort
Product Reviews
★★★★★ 4
Good but Installation was a Bit Iffy
Model: iPad A16 11th/10th/Air 11
90% of the time I use my iPad for school. Originally, I used just a regular screen protector, but it would get dirty with smudges and imprints from my Apple Pencil, and there would be a lot of glare since I'm in a classroom most of the time, which would make it awkward to see what I was writing at times. Plus, the screen protector was too smooth so it would actually be difficult to write legibly.
This product makes it a lot easier to write smoother on the iPad. I only just installed it, so I can't say much on the smear protection yet, but I can already see the reduction in glare as well. For $8, getting a pack of two of these with an install kit is a very nice deal imo.
My only issue was the installation process, which could've been as much my own fault tbh, but I felt like I aligned the screen protector pretty well with the sticker, however the first time I tried installing it it was way off the center (maybe my case got in the way?). The biggest issue was using the squeegee to pop air bubbles, and this is something they don't mention in neither their instruction guide nor video, but you're supposed to used the velvet red side, not the naked white side: using the white side actually takes the grit off the protector, which is obviously something you don't want on a product that relies on it. Thankfully I have another one in reserve in case this one wears off sooner than expected.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 7, 2025
★★★★★ 5
Perfect Paperlike substitute
Model: iPad Air/Pro 13
I’ve been using this screen for roughly two months now and I can say it was so worth it, it is rough on plastic nibs! I am going to order some heavier duty ones and see how it fairs! It works just fine ON TOP of a screen protector isn’t that great!
I wanted something like paper like but didn’t want to pay that expensive price for something I wasn’t sure I was going to like. This one does the trick and gives me just enough resistance to feel more in control of my pen!
It fits well just make sure to know the size if your screen I had to modify where the camera indent was but it cut just fine and looks great!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 24, 2026
★★★★★ 5
Wow! So cheap and really high quality!
Model: iPad Air/Pro 13
Very nice texture, affordable, durable, easy to mount. No longer get tons of grease marks from my hands, the glare is reduced, it fits the screen perfectly, there’s no tint to the color so it doesn’t distort the image. Great product for a great price.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 13, 2026
★★★★★ 5
Feels like paper and makes writing fun!
Model: iPad A16 11th/10th/Air 11
I was hesitant to start using my iPad for class because I HATED how my Apple Pencil sounded hitting the screen while I was writing.
This product has completely changed my mind and now I use it almost daily! I love the feel of this screen and it has lasted all semester long. It was a little tricky getting the screen on just right, and I had to use both because the first time I had a bunch of air bubbles, but the second time was perfect! I think you would probably want to get a new screen every year to ensure it still has that paper-like feel, but I think that’s totally reasonable!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 24, 2026
★★★★★ 5
Game changer for Note Taking
Model: iPad A16 11th/10th/Air 11
Great quality, great price, easy to apply. Has completely changed the way I use my iPad and how it feels to write on it.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 23, 2026