Aguilar OBP3SKPPSET 3-Band Stacked Boost/Cut On Board Bass Preamp with Toggle

Aguilar OBP3SKPPSET 3-Band Stacked Boost/Cut On Board Bass Preamp with ToggleOBP 12 BAND, BOOST9 OR 18 VOLT ON BOARD PREAMP The OBP 1s boost only design gives you the tone shaping benefits of active electronics without losing the inherent sound of the instrument. The OBP 1s discrete, all FET circuitry features up to 18dB of boost at 40Hz and 4kHz, creating a sonic environment high in dynamic headroom and low in noise. OBP 1 FEATURES All FET design Two bands of boost Maximum amount of boost: 18db, occuring at 40 Hz for the

OBP-1
2 BAND, BOOST
9 OR 18 VOLT ON BOARD PREAMP

The OBP-1’s boost-only design gives you the tone shaping benefits of active electronics without losing the inherent sound of the instrument. The OBP-1’s discrete, all-FET circuitry features up to 18dB of boost at 40Hz and 4kHz, creating a sonic environment high in dynamic headroom and low in noise.

OBP-1 FEATURES

• All FET design
• Two bands of boost
• Maximum amount of boost: 18db, occuring at 40 Hz for the bass, and 4kHz for the treble
• Output impedance: 600 ohm
• Dimensions: 0.98W” x 0.98L” x 0.59D”
• Warranty: Three year limited warranty
• Available in the following kits:
• OBP-1TK: Includes separate Treble and Bass pots.
• OBP-1SK: Includes stacked Treble/Bass pot.

OBP-2
2 BAND, BOOST/CUT
9 OR 18 VOLT ON BOARD PREAMP

The OBP-2 was designed to give bassists fat tone while being small enough to fit into tight control cavities. Wire this preamp with one 9 volt battery and it will fit into just about any instrument. With +/-18dB of boost and cut at 40Hz and +/- 16dB of treble boost and cut at 6.5 kHz you have can emphasize just the right frequencies to make your bass sound great in any mix.

OBP-2 FEATURES

• Bass control: plus/minus 18 dB @ 40 Hz
• Treble control: plus/minus 16 dB @ 6.5 KHz
• Input impedance: 1 meg ohm
• Output impedance: 100 ohm 9 or 18 volts operation
• Distortion: .019 into 10k ohm load
• Noise: -95 dBm unweighted.
• Battery life: 324 hours
• Wire lead length: 6.50 inches
• Low noise discrete FET input stage, center detent 50 K linear pots, with a dual concentric pot available
• Dimensions: 0.98″W x 0.98″L x 0.59″D
• Warranty: Three year limited warranty.
• Available in the following kits:
• OBP-2TK: Includes separate Treble and Bass pots
• OBP-2SK: Includes stacked Treble/Bass pot

OBP-3
3 BAND, BOOST/CUT
9 OR 18 VOLT ON BOARD PREAMP

The OBP-3 is Aguilar’s most flexible onboard preamp design, providing +/-18dB of cut and boost at 40Hz, +/- 16dB of cut and boost at either 400Hz or 800Hz and +/- 16dB of treble cut and boost at 6.5 kHz. The OBP-3 has multiple wiring options, and can be wired with either a push/pull pot OR mini-toggle for midrange frequency selection.

OBP-3 FEATURES

• Bass control: plus/minus 18 dB @ 40 Hz
• Mid control: plus/minus 16 dB @ 400Hz or 800 Hz. User selectable frequency center
• Treble control: plus/minus 16 dB @ 6.5 KHz
• Input impedance: 1 meg ohm
• Output impedance: 100 ohm 9 or 18 volts operation
• Distortion: .019 into 10k ohm load
• Noise: -95 dBm unweighted
• Battery life: 324 hours
• Wire lead length: 6.50 inches
• Low noise discrete FET input stage, center detent 50 K linear pots,with a dual concentric pot available
• Dimensions: 0.98″W x 0.98″L x 0.59″D
• Warranty: Three year limited warranty
• Available in the following kits:
• OBP-3TK: Includes separate Treble, Mid, and Bass pots, and black mini-toggle switch for Midrange frequency selection
• OBP-3TK/PP: Includes separate Treble, Mid, and Bass pots. Mid pot is push/pull for Midrange frequency selection
• OBP-3SK: Includes stacked Treble/Bass pot, Mid pot, and black mini-toggle switch for Midrange frequency selection
• OBP-3SK/PP: Includes stacked Treble/Bass pot and separate Mid pot. Mid pot is push/pull for Midrange frequency selection