Pay in installments of $200.12 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Aug 29 - Sep 3
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Link G4x Plug-In ECU for Subaru Impreza WRX & STI V7-9 - 229-4000WRX9X Read more about our Fitting and Mapping service HERE The Link G4+ range of engine management systems are already well known for delivering class leading performance without sacrificing factory levels of drivability. The G4x takes this a step further with massively enhanced logging, mapping, maths and channel configuration. The G4x plug in ECUs are designed to be the most complete plug in solution yet. This V7 9 WRX STI plug in ECU will save you
WRX9X
Read more about our Fitting and Mapping service HERE
The Link G4+ range of engine management systems are already well known for delivering class-leading performance without sacrificing factory levels of drivability.
The G4x takes this a step further with massively enhanced logging, mapping, maths and channel configuration.
The G4x plug-in ECUs are designed to be the most complete plug-in solution yet.
This V7-9 WRX/STI plug-in ECU will save you time and money as it will plug straight into the vehicle’s original wiring loom without the need for messy adaptor harnesses. It replaces the original circuit board inside the factory ECU enclosure and mounts using the factory brackets.
This Link G4x Subaru WRX/STI plug-in ECU is suitable for the models listed below:
Subaru Impreza Version 7-9 WRX & STI Impreza WRX & STI (GD/GG chassis, MY2001-2007 with cam control. 2.0L models only)
Once the installation is complete, the Link G4x allows a good tuner to achieve an optimal state of tune to get the most out of any combination of modifications.
All Link G4x plug-in ECUs come with a base map. While these maps are designed to help save time for you and your tuner, it is essential that these are used simply as a starting point for further tuning.
The engine can easily be converted to speed density by removing the air flow meter and instead using a suitable MAP and air temperature sensor. Likewise, this ECU can also be setup to control boost electronically with in-cabin adjustment. This eliminates the need to purchase a separate electronic boost control system.
The vehicle’s original sensors & actuators are used except for the following exceptions:
- MAP sensor – For all models the factory MAP sensor is supported. These sensors are capable of measuring up to 1.64Bar (23.5psi) boost. If more boost is intended to be used a higher rated MAP sensor can be connected to the existing wires. The airflow sensor is not required.
- Inlet Air Temp sensor (IAT) – An appropriate IAT sensor (available seperately), should be installed just prior the throttle body even on models that have a factory fitted IAT sensor near the airbox and even on Spec C models that typically have a factory fitted IAT sensor in the inlet manifold. The factory IAT wiring can be used on models that have a factory fitted IAT sensor. On all other models the IAT sensor can be wired via the expansion connector on the ECU using the XS loom.
- Boost control – The factory boost solenoid control wiring is used, however the boost solenoid must be upgraded on applications using an external wastegate or elevated boost levels.
- Injectors – The G4x plug in is NOT designed to be used with low impedance injectors. All the Subaru models this G4x plug-in is designed for use high impedance injectors so no changes are necessary. However if low impedance aftermarket injectors have been fitted then the correct ballast resistors MUST be fitted.
Features
G4X PlugIn Key Features (Where Applicable)
- Up to 6D fuel and ignition mapping
- Precision closed loop cam control (four cam, independent control)
- Sequential fuel delivery
- Digital triggering, all OEM patterns
- OEM idle hardware supported
- 5D boost control with three switchable tables
- Motorsport features - antilag, launch, flat shift
- Continuous barometric correction (on board)
- CAN port
- QuickTune - automated fuel tuning
- Individual cylinder correction
- USB tuning cable included
- Stats recording into on-board memory
- Gear compensations for spark, boost and fuel
- Real time selectable dual fuel, ignition and boost maps
- Sync and crank sensors can be a combination of Hall effect, variable reluctance or optical
- Boost control referenced to gear, speed or throttle position
- 512 megabytes data logging memory
- Staged injection
- Knock with "windowing"
Logging
- 512Mb of 32bit Internal logging memory
- Up to 250 ECU Logging channels
- Up to 1kHz per channel with a maximum total sample rate of 100kSamples/s when using ECU Logging
- Unlimited channels when using PCLink logging
Communications
Tuning Port USB on boardTwo CAN busesCustom CAN configuration allowing tuners and end users to add support for new CAN devicesProcessing
150 MHz Specialised Engine Management MicroprocessorIgnition control to 0.1 degree, fuel to 0.01 ms32 Bit Floating Point Calculation12 Bit ADC Resolution20000+ RPM4Gb Non Volatile FlashEnvironment
Internal Temperature Range -10 - 85oCAmbient Temperature Range -30 - 90oCVoltage 8 - 22VOperating Current 200mAElectrical protection on all inputs and outputsOnboard Barometric Pressure SensorPackaging Contents
G4X PlugInX ECUWiring and Installation Instructions2 large Link Stickers2 small Link StickersManufacturing Standard – ISO 13485
Extra sensor inputs
The expansion connectors on the Link G4x board are provided to allow the easy connection of additional ECU inputs. The two expansion connectors on this particular plug-in model provides the following:
- 2 x 5V Supply
- Sensor ground
- 3 digital inputs
- 6 analogue voltage inputs
- 1 analogue temperature inputs
These may be used for functions such as driver adjustable boost control, switchable fuel/ignition maps, wideband lambda input, external MAP sensor, fuel pressure and oil temp/pressure.
Outputs
Any redundant outputs may be reconfigured & used for alternative uses, eg extra electric fans, intercooler water spray, shift light, water injection
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy