Pay in installments of $643.62 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Aug 27 - Sep 1
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Ashly PEMA 8125.70D 1000W Pema Network Power Amplifier With Opdante Card Amp Protea Dsp Software Suite 70VAshly PEMA 8125. 70D overview The 8 Channel 1000W Pema Network Power Amplifier from Ashly consists of eight inputs and eight power amplifier outputs with the ability to assign any input to any output. The amplifier features pre installed OPDante network audio interface card and the Protea DSP Software Suite. When switched into bridged mono mode, eight powered outputs deliver 75W into an 8 ohm load, 125W into an 4 ohm load, and channel pairs can be
Ashly PEMA 8125.70D overview
The 8-Channel 1000W Pema Network Power Amplifier from Ashly consists of eight inputs and eight power amplifier outputs with the ability to assign any input to any output. The amplifier features pre-installed OPDante network audio interface card and the Protea DSP Software Suite. When switched into bridged-mono mode, eight powered outputs deliver 75W into an 8 ohm load, 125W into an 4 ohm load, and channel pairs can be bridged for 250W into an 8 ohm load.
The power amplifier includes Euroblock input connectors and Euroblock output connectors. Besides remote standby for power up, DC remote level control, and contact closure preset recall, the amplifier also features Ethernet control, level, mute, polarity, temperature, current, and amplifier over current conditions. The front panel indicates power status, standby, protect, power switch On/Off, signal level, bridge, temperature & current levels, and Ethernet communication. A temperature dependent speed-controlled axial fan shall maintain the correct operating temperature. Full programming and control of the unit is from the rear panel RJ-45 jack connected to a 10/100BASE-T Ethernet LAN connected to a PC running the Protea Software. The amplifier mounts in a standard 19” rack using two spaces (3.5” high).
The power amplifier has an internal factory-installed Digital Signal Processing (DSP) controlled using the Protea Software Suite (network-enabled). Each amplifier input channel can be configured with pluggable DSP blocks to have its own dynamics control, gain functions, graphic and/or parametric EQ, Hi-pass/Lo-pass filters, time delay, metering, and test signal generator. Hot-plug DSP placement allows you to insert any function into any channel block, even when running live audio. A mixer section with assignable routing allows any input to drive any or all amplifier outputs. The matrix mixer also has selectable gain sharing automatic mixing capability. Outputs have the same DSP functions as inputs, with the addition of a quick and automated crossover setup. Up to 30 presets shall be standard and four presets shall be accessible via contact closure using the Protea Software Suite.
- 70V constant voltage
- 8x8 DSP matrix with 8-channel power amplifier
- OPDante network audio interface
- FIR Filter capable
- Eight built-in mic preamp outputs
- Gain sharing automatic mixing capability
- Automatic feedback suppression
- Ambient noise compensation
- Telephone/PBX input
- Dual RCA and balanced Euroblock inputs
- Post DSP Aux line level outputs
- Stereo summed to mono
- Event scheduling (RTC)
- Adjustable HP/LP filters
- Built-in pink/white noise & sine wave generator
- Protea DSP software suite
- Hot-plug DSP placement
- 15V phantom power for mic inputs
- Full control using software over 10/100BASE-T Ethernet
- Automatic DHCP network IP configuration
- Euroblock connectors for preset recall, DC remote level control, and serial data control
- External control via standard wall remotes, Ethernet wall remotes, Remote iPad app
- Level control via variable DC control voltage
- Stand-by mode activation via contact closure
- Multi-level security
- cTUVus, CE, FCC, & RoHS safety/compliance
-
nly available w/ 48 kHz sampling rate (inputs only)
Filters: 12
In/Out per filter: Yes
Filter Modes: Float, Restricted, Manual
Filter Type: Notch, Parametric
Filter Frequency Range: 20 Hz to 20 kHz
Parametric Filter Level: +15 to -30 dB
Filter Bandwidth: 0.016 to 3.995 Octave
Detector Sensitivity: 5 levels
Float Time: 5 minutes to 24 hoursCrossover 2 Way, 3 Way, 4 Way Crossover & High-Pass/Low-Pass Filters
Bessel & Butterworth Filters: 12/18/24/48 dB/oct
Linkwitz-Riley Filter: 12/24/48 dB/oct
Frequency: Off, 20 Hz to 20 kHzDelay @ 48 kHz Sampling Rate (Input Time, Distance & Temperature)
Speaker Delay: 0 to 21 ms
Delay: 0 to 682 ms
@ 96 kHz Sampling Rate (Input Time, Distance & Temperature)
Speaker Delay: 0 to 10.6 ms
Delay: 0 to 341 msAudio Metering Range: -60 to +20 dBu
Increments: 1 dB
Peak Hold Indicator: YesSignal Generator Pink noise, White noise, Sine wave
Signal Level: Off, -50 to +20 dBu
Sine Wave Frequency: 20 Hz to 12 kHzMixer Mixer
Gain (0.5 dB increments): Off, -50 to +12 dB
Mute: Per channel
Auto-Mixer: Per channel
Global Auto-mixer Response: 0.01 to 2 sec
Enable Ducking at Mixer: Yes
Ducking LED: Per channel if enabled
Metering: Level, auto-mixer levelProcessors Input A/D, Output D/A: 24-bit
DSP Processors: 32-bit floating point
Sample Rates: 48 and 96 kHz
Propagation Delay: 1.42 ms @ 48 kHz & 1.71 ms @ 96 kHz
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy