SKU: 19732449498

Omnibus F4 V6 Flight Controller

Sale price$14.50 Regular price$16.11
Save 10%

Pay in installments of $4.03 with ShopPay, AfterPay and Klarna

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Aug 15 - Aug 20

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

Omnibus F4 V6 Flight ControllerNote: Like all of our Airbot products, this is the genuine original Airbot board not a clone. The omnibus series of flight controllers are known to be the best all in one integrated flight controller, using the best selection of sensors and parts at a great price and small form factor. Now the latest addition to the series uses the performance STM32 F405 MCU. The omnibus F4 uses the MPU6000 ICM 20608 IMU over SPI for the super fast gyro updates (up to

Note: Like all of our Airbot products, this is the genuine original Airbot board - not a clone.

The omnibus series of flight controllers are known to be the best all in one integrated flight controller, using the best selection of sensors and parts at a great price and small form factor. Now the latest addition to the series uses the performance STM32 F405 MCU. The omnibus F4 uses the MPU6000/ICM-20608 IMU over SPI for the super fast gyro updates (up to 32Khz) to keep up with the fast F4 MCU, allowing you to run your betaflight/iNav control loop insanely fast. This gives you the extra edge when racing your FPV quadcopter.

The AB7456 OSD chip (an upgraded MAX7456) allows for direct configuration and updates directly within betaflight. This OSD chip uses much less power than the older MAX7456 OSD Chip, but the main benefit is that it can be configured directly within betaflight, no need for an external FTDI, or jumper switches. In addition the omnibus F4 includes a high performance 5V, 1.5A STM L78 voltage regulator which help filter the power and adds voltage protection to the board.

You can view the omnibus F4 V6 Manual over on dronetrest.com

Omnibus Versions

  • The V6 omnibus has quite a few changes:
    • New firmware target (OMNIBUSF4FW) - after flashing go to CLI and type set gyro_to_use = second , and save to get the IMU working.
    • 5x UART Ports
    • 5V 1A and 8V BEC for FPV camera
    • Current source jumper selecter (see manual for more information)
  • The V5 omnibus includes a current source selection jumper (see pinout below for more details), also the omnibus f4 v5 uses a new 8 pin Sh 1.0 Socket to make connecting a 4in1 ESC much easier. This is compatible with up to 6S batteries.
  • The V4 omnibus main feature is that the solder jumper to selected between PPM/SBUS is no longer needed. The board also features some minor hardware revisions to increase the boards robustness even more.
  • The V3 fixes some of the LDO problems of the V2, so now you can power this board directly from your battery (up to 4S Lipo)

Key Features

  • Tantalum Capacitors added for noiseless gyro reading
  • Solder pads added for SmartAudio and Camera Control (next to Video pads)
  • Added an 8v BEC and LC Filter for the camera and VTX power
  • This board now has 5 UART ports
  • New style layout

Specifications

  • STM32 F405 MCU
  • SBUS input (no PPM input support)
  • 6PWM output
  • Only 36x36mm, mount holes 30.5x30.5mm
  • BMP 280 Baro
  • SPI Sensor MPU6000/ICM-20608
  • 128Mbit Flash
  • Powered directly from 2-6S Lipo (v5 only)

Kit Contents

  • 1x Omnibus F4 Flight controller

We do not include any pin headers with this board, but we do sell them separately on our website.

Zadig Drivers

If you have problems connecting to the board, or uploading new firmware the best fix is to use the zadig driver tool.

  • Push BOOT button on the flight controller.
  • Plug-in the USB cable (the red LED should not be as bright as normally).
  • Fire up Zadig and hit "Options" and then "List All Devices".
  • From the list choose "STM32 BOOTLOADER".
  • Under "Driver" choose "WinUSB" on the right and hit "Reinstall Driver".

For more information check out our zadig driver tool tutorial

Omnibus F4 V6 Pinout

Omnibus F4 V5 Pinout

The V5 omnibus includes a current source selection jumper (see pinout below for more details), also the omnibus f4 v5 uses a new 8 pin Sh 1.0 Socket to make connecting a 4in1 ESC much easier.

Omnibus F4 V4 Pinout

This v4 pinout is for people who still use the older version. The notable feature of the V4 board is that the SBUS/PPM solder selector jumper has been removed, now you can just connect your receiver to J7 and select the type within betaflight.

Omnibus F4 V3 Pinout

The pinout was kept here for previous customer still flying on the V3 omnibus.

Using SBUS/PPM/DSM

There is a known bug with betaflight that can sometimes prevent you from switching between SBUS and PPM. You need to first select serial RX and sbus in the configuration tab, save. Then go turn on serial RX on the UART 6 port in the ports tab and save. Then go back between the two to make sure the settings have been saved correctly as sometimes it does not save properly.

Inverted and non-inverted SBUS

  • SBUS/PPM (J7) header (uart6) This is for inverted signal receivers; has fixed inverter that can not be turned off (by cli command sbus_inverter=on/off)
  • RX1 (on J2) (uart1), These are for non-inverted signal receivers.

Spektrum DSM

  • DSM connector (on J8). This is for non-inverted signal receivers, and is equivalent to RX1.

Arming problems:

  • If you are certain that your board is set up correctly yet it refuses to arm, try raising the gyro noise limit in the CLI using this line: "set gyro_calib_noise_limit = 120"

Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 19732449498

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.7 ★★★★★
Based on 15 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
A
Verified Purchase
Amazon Customer
Pawtucket, US
★★★★★ 5
Get one!
Color: Rubber Chew Toy, Size: Large, Color: Rubber Chew Toy, Size: Large
This was my puppy’s fav toy for the longest time. Not too heavy and is the right amount of tough for a chewing teething puppy. Cute toy that’s easy to chew and safe for a teething puppy it’s not loud and lasts. Worth the price.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on November 14, 2025
S
Verified Purchase
Stacie
Los Angeles, US
★★★★★ 5
Great for large chewers
Color: Rubber Chew Toy, Size: Large
Our dogs very favorite toy. I have bought several in all colors. Good quality and it lasted a while even with my strong dogs.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 22, 2026
C
Verified Purchase
cassie
Houston, US
★★★★★ 5
Hard chewer pass!
Color: Rubber Chew Toy, Size: Large
Our dogs love these! They are hard chewers and am impressed they last a decent while. Good for the price!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 20, 2026
T
Verified Purchase
Today
Lexington, US
★★★★★ 5
Airedale tough!
Color: Rubber Chew Toy, Size: Large
We have two young Airedale Terriers and I thought this would be a good inside toy for them to tug. And I was right! Very happily so. I have to admit I was surprised when I first saw it; it seemed so small. But the thing stretches and springs back to shape. We’ve had it about 2 weeks now and it is constantly played with. Absolutely the best toy! Very interactive either alone (it rolls) or with us or they play together. I am surprised how tough it is with all the constant rough play. Highly recommend!!!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 12, 2022
J
Verified Purchase
Julie
Cuba, US
★★★★★ 4
Small, but twisty and fun looking. Seems relatively sturdy, though doesn't look indestructible at all.
Color: Rubber Chew Toy, Size: Large
SLIGHTLY disappointed because I thought this was bigger than it is. If you squish it all in close, it's maybe one and a half times the size of a tennis ball. (Of course, the size is probably listed; I think I just assumed, so my fault.) That being said, it's entertainingly twisty and squishy, though the rubber seems relatively sturdy. I'm not yet positive if it will hold up to the 8 month retriever/lab mix it's intended for; he tends to rip instantly through anything much less sturdy than kong natural rubber. But it seems like something that will amuse him, so we're going to give it a shot at Christmas.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on November 7, 2014

recommand products