Pay in installments of $13.75 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Aug 13 - Aug 18
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Lemon RX LM0087T DSMP 10ch Telemetry Stabilizer, T-Plug Energy MeterHighlight The generation 2 DSMP 10 channel telemetry stabilizer is a complete redesign that provides the ultimate reliability, features and performance. DSMX DSM2 compatible, 10 channel full range telemetry stabilizer with full telemetry features including a built in barometer, altimeter, energy meter (Current, Voltage, mAh), and internal temperature sensor High sensitivity gyro with proprietary stabilization algorithm ensures responsive airplane
Highlight
The generation 2 DSMP 10-channel telemetry stabilizer is a complete redesign that provides the ultimate reliability, features and performance.
- DSMX / DSM2 compatible, 10-channel full-range telemetry stabilizer with full telemetry features including a built-in barometer, altimeter, energy meter (Current, Voltage, mAh), and internal temperature sensor
- High sensitivity gyro with proprietary stabilization algorithm ensures responsive airplane control for both electric and gasoline engine application
- High sensitivity gyro with proprietary stabilization algorithm ensures responsive airplane control for both electric and gasoline engine application
- BEC1 and BEC2 dual inputs allow high-reliability operation while improving setup for high current drain performance servo
- Built-in Delta, V-tail and Normal Wing mixer
- Supports stabilization with separated channel dual aileron operation
- Stabilization always-on feature allows nine usable channels on a 10-channel receiver
- Real-time variable stabilization gain control on channel 8
- All-channel failsafe
- Firmware health monitoring software stack and ultra-low operational voltage (3.6V) ensures high operation reliability
- Generation 2 SDR stack ensures the fastest channel searching and advanced algorithm for signal recovery with ultra-low-latency experience
- Antenna diversity improves the reliability of the wireless link
- Satellite port for additional signal diversity
- Gyro stabilization activation with either AUX2 or Gear channel
- 3 potentiometers for individual gain tuning
User manual
Reset stabilizer
- Connect power
- Hold F and B buttons (approximately 5 secs+) until all LED flashes randomly
- Press the C button. Multiple LEDs flash a few times to complete the operation
Bind with bind plug
- Insert bind plug on Channel 10
- Connect power
Bind without bind plug
- Connect power
- Hold the B button until the red LED flashes
Bind with a satellite without a bind plug
- Connect power
- Hold the B button until the red LED flashes
- Disconnect power
- Plug the satellite wire connector into the stabilizer
- Connect power
Failsafe
- Connect power to the receiver and ensure the servos are working with the transmitter
- Press the F button for 3 seconds until green changes from off to on and vice versa to change the failsafe setting. Channel value is saved as failsafe default at the time the green LED turns on.
- Turn off the transmitter and wait 2 seconds to ensure the failsafe is activated accordingly by ensuring there is torque generated with finger-pushing the servo linkage if it was to be set. Vice versa.
Stabilization activation switch
- Disconnect power
- Insert bind plug to channel 8
- Hold the C button
- Connect power. Wait for about 1 second until the 6 LEDs flash.
- Release the C button
- Press C to make changes within 3 seconds. Green = CH7, Blue = CH5.
- Wait for 3 seconds and remove the bind plug
Wing Mode and Dual Aileron
- Disconnect power
- Insert bind plug to channel 9
- Hold the C button
- Connect power. Wait for about 1 second until the 6 LEDs flash
- Check the receiver label/user manual to understand the referred LEDs' operation
- Release the C button
- Observe which red LED is flashing and brief press C to select the required mode
- Press C to toggle between settings. On means selected. Exit automatically in 5 seconds.
- Wait for 3 seconds and remove the bind plug
- Ensure transmitter mixing is set accordingly for dual aileron if stabilized dual aileron is to be configured.
Gyro direction
- Check the receiver label/user manual to understand the referred LEDs' operation
- Connect power and wait 1 second
- Hold the C button and wait for about 1 second until the 6 LEDs flash
- Release the C button
- Observe which red LED is flashing and brief press C to select the required mode
- Press C to toggle between settings. On means selected. Exit automatically in 5 seconds.
- Wait for 3 seconds and remove the bind plug.
V/I sensor calibration
- Turn on the receiver and transmitter. The telemetry report page may optionally be checked during and after calibration.
- Plug the V/I sensor. Make sure the required DC loading device such as a brushless motor with ESC as well as the current and voltage meter is connected.
- Press the F and B buttons together at the same time for 2 seconds but no greater than 5 seconds
- Observe 3 green LED flashes. Ensure 8.4V is provided to the V/I sensor.
- Press F or C button briefly
- Observe 3 red LED flashes
- Turn on the DC loading device by throttling the transmitter. Ensure 4A is drawing across the V/I sensor. Be careful with the motor spinning if it is to be used.
- Press the B button to save and exit.
V/I probe calibration
- Turn on the receiver and transmitter. The telemetry report page may optionally be checked during and after calibration.
- Plug the V/I sensor. Make sure the required DC loading device such as a brushless motor with ESC as well as the current and voltage meter is connected.
- Press the F and B buttons together at the same time for 2 seconds but no greater than 5 seconds
- Observe 3 green LED flashes. Ensure 8.4V is provided to the V/I sensor.
- Press F or C button briefly
- Observe 3 red LED flashes
- Press the B button to save and exit.
Gain setting
- Adjust via the 3 dials or real-time master gain on channel 8 depending on the transmitter channel's availability.
View setting LEDs with all on
- Press the C button briefly (no more than 2 seconds).
Lemon Rx products are tested to be compatible with Spektrum's DSMX and or DSM2 product (Spektrum, DSMX and DSM2 are the registered trademark of Horizon Hobby, Inc.).
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.3 ★★★★★
Based on 21 reviews
Sort
Product Reviews
★★★★★ 1
Is this a Casper or Tempurpedic?
When I went to wash the pillow covering I discovered that it iterally had a Tempurpedic factory pillow covering underneath the Casper factory pillow covering - leading me to believe that it was either a return item shipped out as new, and the previous owner actually returned a Tempurpedic pillow disguised as a Casper, or Casper is actually manufactured by Tempurpedic and uses the Casper brand to upcharge. Either way - it's turned out to be an overly expensive - mediocre pillow.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on July 25, 2025
★★★★★ 2
Does not cool, is hot actually
I am very disappointed with this product. I write a lot of reviews and give credit where credit is due. I wish credit was due here.
I bought this as a gift for my wife. She slept on it for a few nights and finally stated that it never cools and is hot instead. And so I tried it and found the same thing. I bought an inexpensive cooling pillow from Costco and we both found that one to cool a little bit and it isn’t hot.
I’m summary, you don’t always get what you pay for and at $100, this pillow does not deliver. It’s supportive and it seems well made, which is why I give it two stars. But it does not deliver any cooling. Save your money and try a different pillow.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on January 5, 2024
★★★★★ 5
Does what it claims, supportive and eliminates heat.
Size: King (Pack of 1), Style: Single Pack
Its a bit pricey however when it comes to sleep quality im glad to pay for name brand. No tossing or turning to escape to the cold side of the pillow. Feels firm which was concerning at first however once you settle in its very comfortable. Seems to be just how foam pillows are made. Happy with the purchase.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 4, 2022
★★★★★ 5
I have found the PERFECT pillow for me!!!
Size: King (Pack of 1), Style: Single Pack
I just absolutely never write a review on anything, but I have to praise this pillow from the rooftops! I have not slept this comfortably is so many years! I have plushness and support, my neck is in alignment, and when I turn to sleep on my side the pillow doesn’t block my airflow. This pillow is perfectly made for me!!!!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 8, 2022
★★★★★ 5
The Perfect Pillow
Size: Queen (Low Loft)
Finally found the right pillow for me. I have purchased quite a few latex pillows attempting to find the right one. I was apprehensive due to the support description being "extra soft". Yes, it's super soft when you pick it up and squeeze it, but it provides the perfect amount of support for side and back sleeping.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 6, 2026