SKU: 72108141788

SQOON® Afneembaar Snoer 15 m – Geschikt voor Nilfisk VP300, VP600, Saltix 10, VC300 & GM80

$35.96 $39.95
Save 10%
No.2 Bestseller on lamcf.fr >

Pay in installments of $9.99 with ShopPay, AfterPay and Klarna

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Aug 18 - Aug 23

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

SQOON® Afneembaar Snoer 15 m – Geschikt voor Nilfisk VP300, VP600, Saltix 10, VC300 & GM80SQOON Afneembaar Snoer 15 m Geschikt voor Nilfisk VP300, VP600, Saltix 10, VC300 & GM80 Het originele alternatief Het SQOON afneembare snoer is een hoogwaardige vervanging voor diverse Nilfisk stofzuigers. Dit snoer van 15 meter is speciaal ontwikkeld voor de Nilfisk VP300, VP600, Saltix 10, VC300 en GM80. Met dit vervangende onderdeel zorg je dat je stofzuiger weer volledig inzetbaar is en geniet je van maximale bewegingsvrijheid tijdens het

SQOON® Afneembaar Snoer 15 m – Geschikt voor Nilfisk VP300, VP600, Saltix 10, VC300 & GM80

Het originele alternatief
Het SQOON® afneembare snoer is een hoogwaardige vervanging voor diverse Nilfisk stofzuigers. Dit snoer van 15 meter is speciaal ontwikkeld voor de Nilfisk VP300, VP600, Saltix 10, VC300 en GM80. Met dit vervangende onderdeel zorg je dat je stofzuiger weer volledig inzetbaar is en geniet je van maximale bewegingsvrijheid tijdens het schoonmaken.

Extra lange actieradius
Dankzij de lengte van 15 meter heb je een ruime actieradius, waardoor je grotere oppervlakken kunt schoonmaken zonder telkens van stopcontact te hoeven wisselen. Dit bespaart tijd en maakt het werken met je Nilfisk stofzuiger een stuk efficiënter.

Perfecte pasvorm
Het snoer is ontworpen als directe vervanging voor de originele kabels van Nilfisk. Je sluit het eenvoudig aan, zonder ingewikkelde aanpassingen of extra onderdelen. Zo ben je snel weer operationeel.

Robuust en duurzaam
Gemaakt van stevige materialen is dit afneembare snoer bestand tegen intensief gebruik. Het is slijtvast en ontworpen voor langdurige prestaties, zelfs in professionele omgevingen waar Nilfisk stofzuigers veel worden ingezet.

Essentieel accessoire
Een goed werkend snoer is onmisbaar voor de prestaties van je stofzuiger. Met dit SQOON® snoer verleng je de levensduur van je Nilfisk toestel en werk je weer veilig en comfortabel.

O.a. geschikt voor:
Nilfisk VP300
Nilfisk VP600
Nilfisk Saltix 10
Nilfisk VC300
Nilfisk GM80

Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 72108141788

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.5 ★★★★★
Based on 13 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
S
Verified Purchase
Steve M.
Phoenix, US
★★★★★ 5
Works well. You need to drill a 3/8” hole
Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4” towards the stepped part of the alignment tool (this is so you won’t bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8” diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8” diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4” drill first, using plenty of oil, drill all the way through, then use the 3/8” drill, deburr both sides and you should be good to go. People complain that it doesn’t come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure you’re perfectly centered and secure before you start drilling.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
N
Verified Purchase
Nancy filippi
Lexington, US
★★★★★ 5
A must pull your gimbal bearing
You do need to drill a hole but worked perfect
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 26, 2025
R
Verified Purchase
rich911s
Charlottesville, US
★★★★★ 5
Worked for Volvo Penta SX Gimbal Bearing
Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2023
G
Verified Purchase
Greg
Waukegan, US
★★★★★ 5
Great value
This kit worked perfectly on my Alpha one mercury outdrive. I saw a lot of people mention that it was a hassle to drill the hole when you better have all this alignment stuff. I threw it in use my regular drill drill guide and then the second hole was lined up. Pulling Gimble be very easy. I did have to adjust it up at an angle because my bearing was sitting in their crooked and it came out the second time I made the adjustment to the angle. I would highly recommend this.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2024
T
Verified Purchase
Tommy Knapp
Carnegie, US
★★★★★ 1
Unfinished product - doesn't work - waste of money
in order to use this as an installation tool the directions tell you to drill a hole through the 2 inch steel rod..... either this hole should already be drilled, or this should not be advertised as an installation tool..... it will not install any bearings without extensive modification and requires the use of a drill press or a lathe. very dissatisfied that I now have to buy ANOTHER tool just to finish this job because this one doesn't do what it's described to do.... piece of junk... typical amazon garbage.... this is why I haven't used amazon in over a year... they rip you off with garbage.... I should have known better .... don't buy this junk .... Now they say 20 -30 days to get my refund .... Don't waste your time
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 26, 2026

recommand products

zelfportret stanislaw sawiczewski
24.90
portret van jan zembrzuski stanislaw lentz
24.90
Liquitex - Basic Set 12 X 22 Ml
26.90
petten stanislaw osostowicz
24.90
Liquitex - Pro Heavy Body 59Ml Lht Bismuth Yellow Uv 3
12.50