Pay in installments of $55.08 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Aug 18 - Aug 23
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
1994-2024 Diesel HD Heavy Duty Cast Aluminum Rear Differential Cover Brushed (238051010)Description Made in the USA from high quality cast aluminum for strength and optimum heat dissipation. PPEs differential covers offer industry leading fluid cooling. Equipped with internal heat sinks and external cooling fins, increasing the pans surface area helping dissipate heat. This makes for a much cooler and denser oil. Cool, dense fluid lubricates better, which will extend differential service life. To keep the fluid clean, PPE installed its
Description
Made in the USA from high-quality cast aluminum for strength and optimum heat dissipation. PPEs differential covers offer industry-leading fluid cooling. Equipped with internal heat sinks and external cooling fins, increasing the pans surface area helping dissipate heat. This makes for a much cooler and denser oil. Cool, dense fluid lubricates better, which will extend differential service life.
To keep the fluid clean, PPE installed its exclusive high-powered Neodymium magnet equipped fill plug will pull harmful ferrous metal particles right out of the oil before they have a chance to attack the bearings and gears.
Features
- Premium A356.0-T6 heat-treated cast aluminum alloy - a high-strength, thermally conductive material
- Precision-cast using permanent steel molds for a smooth, consistent finish and high dimensional accuracy
- Increases oil capacity by .63 quart for higher thermal capacity
- Half-inch external fins improve heat dissipation, lower differential fluid temperature, and increase impact resistance
- Precision-placed internal windage scrapers prevent excessive churning, reducing heat generation, fluid aeration, and power loss
- External fins and internal scrapers work together to form an ultra-strong Cross-Bracing structure
- Cast-in gussets for additional differential housing flange support and increased rigidity
- 304 Stainless steel service plugs with built-in high temperature rated neodymium magnets and Viton O-rings
Notes
- Only works with vehicles equipped with AAM 11.5"-14 axles.
- Not compatible with certain 2003-2012 Dodge Ram HD trucks equipped with Anti-Spin Differential rear axles due to the tone ring sensor; for these applications see the 2001-2019 GM, 2001-2018 RAM AAM 11.5"-14-Bolt Heavy-Duty Cast Aluminum Rear Differential Cover (P/N 138051000).
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.0 ★★★★★
Based on 8 reviews
Sort
Product Reviews
★★★★★ 5
Works well. You need to drill a 3/8” hole
Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4” towards the stepped part of the alignment tool (this is so you won’t bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8” diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8” diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4” drill first, using plenty of oil, drill all the way through, then use the 3/8” drill, deburr both sides and you should be good to go. People complain that it doesn’t come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure you’re perfectly centered and secure before you start drilling.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
★★★★★ 5
A must pull your gimbal bearing
You do need to drill a hole but worked perfect
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 26, 2025
★★★★★ 5
Worked for Volvo Penta SX Gimbal Bearing
Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2023
★★★★★ 5
Great value
This kit worked perfectly on my Alpha one mercury outdrive. I saw a lot of people mention that it was a hassle to drill the hole when you better have all this alignment stuff. I threw it in use my regular drill drill guide and then the second hole was lined up. Pulling Gimble be very easy. I did have to adjust it up at an angle because my bearing was sitting in their crooked and it came out the second time I made the adjustment to the angle. I would highly recommend this.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2024
★★★★★ 1
Unfinished product - doesn't work - waste of money
in order to use this as an installation tool the directions tell you to drill a hole through the 2 inch steel rod..... either this hole should already be drilled, or this should not be advertised as an installation tool..... it will not install any bearings without extensive modification and requires the use of a drill press or a lathe. very dissatisfied that I now have to buy ANOTHER tool just to finish this job because this one doesn't do what it's described to do.... piece of junk... typical amazon garbage.... this is why I haven't used amazon in over a year... they rip you off with garbage.... I should have known better .... don't buy this junk .... Now they say 20 -30 days to get my refund .... Don't waste your time
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 26, 2026
recommand products
Advan TC4 16x6.5 +45 4x100 Racing Candy Red and Ring Wheel
258.50
Government Recommended Emergency Preparedness Kit
296.00
Advan R6 18x10.5 +24 5x114.3 Racing Titanium Black Wheel
539.00
Advan R6 18x9.5 +45 5x120 Racing Titanium Black Wheel
523.00
Advan TC4 15x6.5 +40 4x100 Racing Candy Red and Ring Wheel
218.50