Pay in installments of $83.55 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Aug 18 - Aug 23
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
5x SX200 Industrial Shelving - 2440mm High - 200kg - Steel - BlueKey Features of SX200 Steel Shelving Holds up to 200kg UDL per shelf (up to 915mm wide) Total load capacity of up to 1,000kg UDL per unit Steel galvanised decks 4, 5 or 6 level options for each unit Additional levels are available separately to suit storage requirements Steel support beams for each level for extra reinforcement 915mm wide units are supplied with 1x support beam per level 1220mm wide units are supplied with 2x support beams per level
Key Features of SX200 Steel Shelving
- Holds up to 200kg UDL per shelf (up to 915mm wide)
- Total load capacity of up to 1,000kg UDL per unit
- Steel galvanised decks
- 4, 5 or 6 level options for each unit
- Additional levels are available separately to suit storage requirements
- Steel support beams for each level for extra reinforcement
- 915mm wide units are supplied with 1x support beam per level
- 1220mm wide units are supplied with 2x support beams per level
- High quality, thick steel uprights and beams with a durable powder coated blue finish
- Boltless ‘stud & keyhole’ design
- Suitable for daily use within a commercial/industrial environment
- Low profile shelf beam design maximises storage space
- Construction is quick and easy with no bolts required
- Full range of accessories such as joining tie plates available
- Adjustable shelf height every 3.8cm (1.5 Inches)
- Accessible from both sides, no back cross bracing needed
- Free Rubber Assembly Mallet!
Ideal Uses:
- Regular Picking
- Archive & document storage
- Small parts storage
- Light boxes
- Domestic items
Product Overview
The Storalex SX200 range of medium-duty steel shelving is ideally suited for frequent use, commercial environments where you need sturdy units that will last a lifetime.
This light industrial range is perfect for businesses storing items in stockrooms, storerooms or heavy duty domestic applications such as garages or workshops. Each shelf can support 200kg UDL*, however If you need to increase the shelf weight capacity the SX340 range is a heavier duty version of this product.
Using a boltless ‘stud & keyhole’ design, these tried and tested units have been sold in the UK for over 25 years. Rigorously tested these commercial grade units also comply with all relevant ISO manufacturing quality requirements.
Product spec
SX200 Steel Shelving Guide
Fitting Guide For SX200 Industrial Shelving Units
External Height = H+15mm, Pitch = 38.1mm. Clear height between shelves = (No. x pitch) -94mm
|
Data |
610w |
915w |
1220w |
1525w |
|---|---|---|---|---|
| Upright | One Piece | One Piece | One Piece | One Piece |
| Shelf Adjustment (mm) |
38.1 | 38.1 | 38.1 | 38.1 |
| Clear Entry (mm) |
546 | 851 | 1156 | 1461 |
| First unit External (mm) | 620 | 925 | 1230 | 1535 |
| Additional unit External (mm) | 627 | 932 | 1237 | 1542 |
| Total unit Capacity 1830h mm | 1200kg | 1200kg | 1200kg | 1200kg |
| Total unit Capacity 2440h mm | 1000kg | 1000kg | 1000kg | 1000kg |
| Upright Steel Thickness (mm) | 1.5 | 1.5 | 1.5 | 1.5 |
| Beam Steel Thickness (mm) | 1.5 | 1.5 | 1.5 | 1.5 |
| Chipboard Thickness (mm) | 15 | 15 | 15 | 15 |
| Melamine Thickness (mm) | 15 | 15 | 15 | 15 |
| Steel Thickness (mm) | 0.8 | 0.8 | 0.8 | 0.8 |
| Height of Shelf (mm) | 30 | 30 | 30 | 30 |
Instructions
Delivery / Returns
[Description 2]
Key Features:
- Up to 200kg per shelf, 1,000 per unit (UDL)
- Flush fitting sheet steel decks
- Adjustable shelf height every 3.8cm
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.2 ★★★★★
Based on 11 reviews
Sort
Product Reviews
★★★★★ 5
Works well. You need to drill a 3/8” hole
Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4” towards the stepped part of the alignment tool (this is so you won’t bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8” diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8” diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4” drill first, using plenty of oil, drill all the way through, then use the 3/8” drill, deburr both sides and you should be good to go. People complain that it doesn’t come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure you’re perfectly centered and secure before you start drilling.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
★★★★★ 5
A must pull your gimbal bearing
You do need to drill a hole but worked perfect
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 26, 2025
★★★★★ 5
Worked for Volvo Penta SX Gimbal Bearing
Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2023
★★★★★ 5
Great value
This kit worked perfectly on my Alpha one mercury outdrive. I saw a lot of people mention that it was a hassle to drill the hole when you better have all this alignment stuff. I threw it in use my regular drill drill guide and then the second hole was lined up. Pulling Gimble be very easy. I did have to adjust it up at an angle because my bearing was sitting in their crooked and it came out the second time I made the adjustment to the angle. I would highly recommend this.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2024
★★★★★ 1
Unfinished product - doesn't work - waste of money
in order to use this as an installation tool the directions tell you to drill a hole through the 2 inch steel rod..... either this hole should already be drilled, or this should not be advertised as an installation tool..... it will not install any bearings without extensive modification and requires the use of a drill press or a lathe. very dissatisfied that I now have to buy ANOTHER tool just to finish this job because this one doesn't do what it's described to do.... piece of junk... typical amazon garbage.... this is why I haven't used amazon in over a year... they rip you off with garbage.... I should have known better .... don't buy this junk .... Now they say 20 -30 days to get my refund .... Don't waste your time
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 26, 2026
recommand products
UH-1 Huey / US Border Patrol Airplane Model
134.49
Jersey Capri Leggings (Charcoal)
26.00
690 Turbo Commander / Rockwell Airplane Model
169.97
B-52 Stratofortress / 69th Bomb Squadron Airplane Model
189.78
Manley 90-00 Mitsubishi Eclipse GS GST 2.0L (4G63-4G63T) DOHC 16 Exhaust 31.5mm Stainless Race Flo
34.64